Automotive Investment Casting for Lightweighting: From Engine Components to EV Battery Housings

For automotive engineering teams, weight reduction remains one of the most significant challenges. Reducing vehicle mass improves acceleration, fuel efficiency, emissions levels and driving dynamics. This is true of combustion engines and even more so in electric vehicles. A heavier vehicle requires a larger battery pack to achieve a given range, but a larger battery pack adds further weight and increases energy demands. Engineering teams tasked with breaking this cycle rely increasingly on lightweighting strategies, and investment casting is one of the most powerful approaches available.

Investment casting delivers the ideal combination of geometric complexity, material versatility, and dimensional precision that automotive lightweighting demands.

For OEMs and Tier 1 suppliers seeking to meet fleet emissions targets, extend EV range, and maintain structural performance while reducing mass, understanding the capabilities of investment casting is important and helps select a supplier with a proven automotive manufacturing track record.

Why Every Gram Counts in Automotive Engineering

Regulatory frameworks continue to push for reduced fleet CO₂ targets across Europe, North America, and Asia. This propels the automotive industry to transform, with a systematic mass reduction across every vehicle system.

For battery-powered electric vehicles, the importance of lightweighting is even greater. Battery packs in current-generation EVs can account for around 20 to 30% of total vehicle weight, enormous when compared to standard combustion engines. Every kilogram removed from the body structure, chassis, or drivetrain reduces the energy demand on the battery. This enables either an extended vehicle range using the same pack size or allows a smaller, lighter, cost-efficient pack to achieve equivalent range targets. As a result, commercial and competitive implications of effective lightweighting in EV architecture are substantial, and the pressure on component suppliers to contribute mass savings at every design review is intense.

Investment casting addresses the lightweighting challenge through two complementary directions. First, it enables the use of lightweight alloys, particularly aluminium, in components that must also meet demanding structural, thermal, and dimensional requirements. Second, it enables the design of components with optimised geometry, including thin walls, internal ribbing structures, hollow sections, and part consolidation that deliver structural performance with minimum material.

This is not a marginal contribution. In automotive programmes where engineers track mass budgets in single-digit grams, the ability to redesign a cast component for weight reduction while maintaining or improving performance is a genuine programme differentiator.

Investment Casting in Traditional Powertrain Applications

Long before electrification became crucial to automotive engineering, investment casting was already delivering weight reduction advantages and measurable performance in internal combustion engine powertrains.

High-volume automotive applications where investment casting has replaced heavier or less capable manufacturing methods include:

  • Exhaust manifolds
  • Turbocharger housings
  • Exhaust gas recirculation components
  • Oil pump bodies
  • Camshaft bearing caps
  • Transmission valve bodies

Turbocharger housings are a strong example of the performance requirements addressed by investment casting. Operating at exhaust gas temperatures that can exceed 1,000°C in performance applications, turbocharger housings require alloys with exceptionally high-temperature strength and oxidation resistance, typically nickel superalloys, formed into volute geometries with precise throat dimensions and smooth internal surfaces that maximise aerodynamic efficiency. Investment casting delivers all of these requirements in a single operation, producing near-net-shape housings and turbo wheels that require minimal post-cast machining and achieve the dimensional accuracy needed for turbocharger cartridge assembly.

Texmo Blank's automotive investment casting capability spans the full range of traditional powertrain applications, including extensive experience with demanding alloys such as Inconel 713C, Inco 2.4671, and related nickel superalloys used in turbocharger and exhaust applications. Consistently casting these materials with the dimensional accuracy and surface integrity required by automotive OEMs demands process control standards that relatively few global casting suppliers can demonstrate.

Aluminium Investment Casting for Automotive Lightweighting

While nickel superalloys represent some of the most technically demanding investment casting applications, aluminium alloys represent some of the most strategically important for automotive lightweighting.

Aluminium offers a density approximately one-third that of steel, with mechanical properties that, when correctly specified and processed, are suitable for a wide range of structural and semi-structural automotive applications. Over the past two decades, the shift from ferrous to aluminium castings across chassis, suspension, and body structure components has been one of the most significant mass reduction levers available to automotive engineers.

Aluminium investment casting delivers advantages that pressure die casting and sand casting cannot easily replicate. The process achieves tighter dimensional tolerances on complex geometries, produces superior surface finishes on critical mating faces and sealing surfaces, and enables wall thickness reductions that are not achievable in sand casting without risking cold shuts or misruns. Aluminium investment casting offers a compelling combination of performance and weight for structural components where both mass and dimensional accuracy are critical, such as suspension knuckles, bracket assemblies, and differential housings.

Texmo Blank's investment casting materials portfolio includes A-356 aluminium, EN AC-42000-T6, and other automotive-grade aluminium alloys processed through both air-melt and vacuum-assisted routes that minimise oxide inclusions and porosity in structurally critical components. The mechanical property requirements for aluminium structural castings, particularly elongation values that provide crash energy absorption, demand process controls that go significantly beyond those applied to non-structural aluminium castings, and Texmo Blank's quality systems are calibrated to these standards.

Lightweighting in EV Battery Housings

The transition to battery electric vehicles has created new categories of automotive casting demand that did not exist a decade ago. The battery housing is among the most demanding new component categories the automotive casting industry has encountered.

EV battery housings must simultaneously achieve a demanding and partially conflicting set of requirements. They must be as light as possible to maximise the range advantage, but they must also be structurally stiff to protect cell integrity in normal operation and during crash events. They must manage heat effectively, incorporating cooling channels or interfaces that maintain cell temperature. And they must also prevent water and debris ingress.

Investment casting contributes to battery housing design in multiple ways. Complex aluminium casting sections that form the structural frame of the housing can be produced with integrated cooling channel provisions, mounting boss geometries, and crash structure features that would require multiple separate components in alternative manufacturing approaches. Part consolidation, which is reducing a multi-part welded or bolted assembly to a single precision casting, simultaneously reduces weight, eliminates assembly interfaces that can become leak paths, and removes the dimensional stack-up uncertainties that complicate multi-part structures.

Texmo Blank brings design engineering expertise to complex automotive casting development and is particularly valuable in EV battery housing applications, where the design space is still evolving. Here, early supplier engagement; at the concept stage rather than after the design is fixed; can influence mass budgets, manufacturing feasibility, and total system cost in ways that downstream supplier selection cannot.

Weight Reduction Through Geometry

Wall thickness reduction is the most direct route to weight reduction in a cast component. Investment casting enables thinner walls than sand casting on equivalent geometries, typically achieving minimum wall thicknesses of 1.5 to 2mm in aluminium and 2 to 3mm in steel, compared to the 4 to 6mm minimums typical of sand casting. For a large automotive housing component, the difference between 3mm and 5mm average wall thickness across a surface area of several hundred square centimetres translates into hundreds of grams of mass reduction per component.

Furthermore, investment casting enables ribbing and structural optimisation strategies that deliver performance-equivalent stiffness at lower total material content. Internal ribs, gussets, and boxed sections that would be difficult or impossible to incorporate in sand casting can be integrated into investment castings, allowing structural engineers to place material precisely where stress analysis indicates it is needed and remove it from regions where it contributes nothing to performance. This topology-informed approach to casting geometry is increasingly enabled by FEA-driven design tools, and investment casting is the process that can execute the resulting organic geometries with the precision and repeatability production demands.

Understanding the dimensional capabilities and weight ranges that investment casting can achieve for automotive applications is the starting point for any weight reduction initiative that incorporates casting redesign. Texmo Blank's engineering team works from existing component designs or from clean-sheet briefs to identify the weight reduction potential that investment casting offers: a conversation that often reveals hidden opportunities from within the constraints of the incumbent manufacturing process.

Prototyping for Weight Reduction Validation

Automotive lightweighting programmes need to balance the pressure to reduce mass against the absolute requirement to maintain structural and functional performance. A component redesigned for weight reduction that fails a durability test has not saved mass; it has consumed programme time and budget that must now be spent on recovery. The imperative to validate weight-reduced designs quickly and cost-effectively before committing to production tooling makes prototyping capability a genuinely strategic asset.

Texmo Blank's prototyping capability for investment casting, spanning rapid wax patterns produced from 3D print data, metal prototyping routes, and wax die prototypes for near-production validation, enables automotive engineers to test weight-reduced designs in the intended alloy under representative loading conditions, without the lead time and cost of full production tooling. Iterating a wall thickness reduction or a rib geometry change at the prototype stage costs a fraction of what the same iteration costs after production tooling is committed.

For EV battery housing development programmes, the ability to move from concept geometry to tested aluminium prototype casting within weeks rather than months compresses the design validation timeline in ways that translate directly into accelerated time to market. This is a competitive advantage that matters as much as the mass saving itself when EV programmes are racing to market.

In-House Assembly and the Total Cost of Lightweighting

Weight reduction is most valuable when it is achieved without a corresponding increase in total system cost. A casting that saves 200 grams but requires additional machining, assembly operations, or quality inspection overhead may not deliver a net programme benefit when all costs are accounted for. Therefore, the total cost of ownership perspective is central to any serious automotive lightweighting initiative.

Texmo Blank's in-house assembly and testing capability allows weight-optimised castings to be delivered as tested, assembled sub-systems rather than individual components requiring customer-side assembly. For automotive customers, receiving a pre-assembled, dimensionally verified, pressure-tested component reduces assembly cost, eliminates the dimensional stack-up risk of multi-part assembly, and shortens the incoming inspection process. Mass saving and cost saving are delivered together.

Supply Continuity for Automotive Production Programmes

Automotive production programmes and their scheduling are highly demanding. A casting supplier who cannot maintain consistent quality and on-time delivery across high-volume, multi-year programmes is a liability that automotive procurement teams are not willing to carry. Natural demand fluctuations, material availability challenges or operational disruptions cannot be accepted excuses.

Texmo Blank's dual sourcing model across manufacturing facilities in the USA, Germany, India, and Romania provides automotive customers with the supply chain resilience that protects against single-source risk. Being able to dual source from the same company helps reduce risk from global shipping delays, regional conflicts or disasters without complicating communication or supply chains.

Complementing this, Texmo Blank's on-time delivery performance and smart warehousing and distribution capability support the sequenced, just-in-time delivery models that automotive customers operate. This ensures that weight-optimised castings arrive at the assembly line when they are needed, in the condition they are needed, without the buffer stock and logistics complexity that supply uncertainty forces onto procurement teams.

Investment Casting is a Lightweighting Strategy, not Just a Manufacturing Choice

Automotive weight reduction is a programme-level strategy that touches every component category, material choice, and manufacturing process selection across a vehicle platform. Investment casting earns its place in that strategy, and not just because it can produce a lighter component but also because it can meet the geometric complexity, dimensional precision, material performance, and supply chain reliability requirements that automotive production demands.

From proven turbocharger and exhaust applications in ICE powertrains, through aluminium structural castings in chassis and body systems, to the emerging frontier of EV battery housings and electric drivetrain components, Texmo Blank has the alloy capability, engineering depth, and automotive programme experience to support lightweighting ambitions across the full vehicle architecture.

To discuss your automotive lightweighting casting requirements, whether you are redesigning an existing component for mass reduction, developing a new EV platform component, or qualifying a casting supplier who can support your programme from prototype through to high-volume production, explore Texmo Blank’s automotive casting capabilities, case studies, or schedule an introduction call with the New Relations Team.

Further Information

Get In Touch

We take pride in building successful, long-term relationships with our clients, because their reputation is our priority.

If that sounds like an investment castings partner you’d like to work with, you can book an introduction call with our friendly and knowledgeable New Relations Team — in a language and time zone to suit you.

:

United Kingdom

+44 114 399 5710

uk@texmoblank.com

:

United States

+1 574 696 9990

usa@texmoblank.com

:

Germany

+49 7371 1820

germany@texmoblank.com

:

Romania

+40 256 22 7817

romania@texmoblank.com

:

India

+91 425 920 0500

india@texmoblank.com